GASES · 6 MIN LESSON

Build the gas model before calculating

A concise core lesson, followed by independent practice.

Practice this topic (sign in required)
RELATED LECTURE · MIT OPENCOURSEWARE

The Importance of Chemical Principles

A supporting university lecture. The written lesson and check can be used independently.

Loads YouTube and shares request information with Google.

MIT source & transcript · Catherine Drennan · 5.111, Fall 2014 · CC BY-NC-SA; source terms

THE CONCEPT

The ideal gas model treats particle volume and intermolecular attraction as negligible. Use absolute temperature and a gas constant that matches your pressure and volume units.

The core relationship

PV=nRT,pi=xiPPV=nRT, \quad p_i=x_iP
WORKED EXAMPLE

0.100 mol at 300 K in 2.46 L gives P = 1.00 atm using R = 0.0820 L atm mol⁻¹ K⁻¹. For a mixture, each partial pressure is its mole fraction times the total.

The common trap

Equal temperatures imply equal average translational kinetic energies, not equal molecular speeds.

Go deeper

Attractive and excluded-volume effects compete in the van der Waals equation; which dominates depends on conditions.

The additional instruction below was developed with AI assistance and awaits independent educator review.

How to approach a problem

For a fixed amount of ideal gas, combine the gas law at the initial and final states: P₁V₁/T₁ = P₂V₂/T₂. Temperature must be in kelvin and pressures must be absolute. For a gas collected over water, subtract the water vapor pressure from the total pressure to obtain the dry gas pressure before using PV = nRT.

Another worked example

A gas occupies 2.00 L at 1.00 atm and 300 K. At 1.50 atm and 450 K, its ideal-gas volume is V₂ = 2.00 × (1.00/1.50) × (450/300) = 2.00 L. The pressure and temperature changes have opposing effects on volume.

Check your reasoning

Convert °C to K before forming a temperature ratio. The combined gas law assumes the amount of gas is unchanged.

Try a reviewed sample

No account required. Sample results stay on this device.

SEL-0089

Gas collected above water

A reaction gas is collected over water at a total pressure of 98.0 kPa. The water vapor pressure at the collection temperature is 3.2 kPa. Assuming no other gas and equilibrium saturation, what is the dry reaction-gas partial pressure?

Human-reviewed originalSolve this sample →
SEL-0092

Temperature and intermolecular motion

Two samples of the same ideal gas have temperatures 250 K and 1000 K. For the same molecular mass, the root-mean-square speed obeys u_rms=√(3RT/M). What is the hot-to-cold speed ratio?

Human-reviewed originalSolve this sample →
SEL-0094

Mean free path under compression

For an ideal dilute gas of unchanged molecular collision diameter d, mean free path is λ=k_BT/(√2πd²P). Compress it isothermally until its pressure triples. Which paired statement is correct?

Human-reviewed originalSolve this sample →
SEL-0102

A throttling inversion criterion

In a supplied low-pressure model, the Joule–Thomson coefficient is μ_JT=[2a/(RT)−b]/C_p, with C_p>0. Let a=2.000 L² bar mol⁻², b=0.05000 L mol⁻¹ and R=0.08314 L bar mol⁻¹ K⁻¹. For an isenthalpic pressure drop, which comparison between 500 K and 1500 K follows?

Human-reviewed originalSolve this sample →
SEL-0443

Gas-density association needs a conserved molecular-unit pool

A gas initially consists of monomer M with molar mass 40.0 g mol⁻¹. At the measurement temperature it equilibrates only through 2M⇌M₂. Apparent mean molar mass from ideal gas density is 50.0 g mol⁻¹. What fraction of monomer units are in dimers?

Human-reviewed originalSolve this sample →
SEL-0467

Wet collected gas measures an electrolysis charge fraction

Hydrogen from a cathode is collected over water. Total gas pressure is 1.00 bar and water vapor pressure is 0.040 bar. The wet-gas volume and temperature would correspond to 0.0100 mol if all pressure were H₂. A total 0.0250 mol electrons passed. H₂ formation requires two electrons per molecule. What hydrogen-producing current fraction follows?

Human-reviewed originalSolve this sample →